Version 2/11/14 INSTALLATION, OPERATION & MAINTENANCE MANUAL FARHENHEIT™ J-F & JX-F SERIES SIDE DISCHARGE Electric Submersible Pumps Singl
10 PUMP OPERATION This pump is designed to handle dirty water that contains some solids. It is not designed to pump volatile or flammable l
11 TYPICAL AUTOMATIC DEWATERING INSTALLATION NOTE: Maximum recommended starts should not exceed 10 times per hour. STOPPING To stop the pump (man
12 Figure 1 Single Phase 400F-115 and 750F-115 Control Figure 2 Single Phase 400F-230, 750F-230 and 1500F-230 Control
13 OPTIONAL FLOAT CONNECTION BJM Pumps utilizes a control for all of the single phase “F” series pumps. The wiring diagram included in this manua
14 TROUBLE SHOOTING Disconnect the power source to the pump BEFORE attempting any type of trouble shooting, service or repair. PUMP WILL NOT RU
15 Cut or cracked power cables must be replaced. (Never operate a pump with a cut, cracked or damaged power cable.) Seal oil should be check
16 EXPLODED VIEW OF J400-F, JX400SS-F
17 EXPLODED VIEW OF J750-F, J1500H-F & J1500HSS F
18 EXPLODED VIEW OF JX750SS-F, JX1500SS-F & JX1500HSS-F
19 J-F SERIES PARTS LIST Pump Model J400F J750F J1500F J1500HFPos. No. Part Description Item # Item # Item # I
20 JX-F SERIES PARTS LIST Pump Model JX400SSF JX750SSF JX1500SSF JX1500HSSFPos. No. Part Description Item # It
21 SINGLE PHASE WIRING DIAGRAM 115V & 230V MODELS: J400-F & JX400-F
22 1150 & 230V MODELS: J750-F, JX750SS-F, J1500-F, JX1500SS-F, J1500H-F, JX1500HSS-F
23 SEAL MINDER® - THERMAL MOTOR SENSOR SWITCH (For high temperature single phase pump models) Seal Minder: Also known as a seal failure circuit (o
24 BJM Pumps, LLC 123 Spencer Plain Road Old Saybrook, CT 06475, U.S.A. WARRANTY AND LIMITATION OF LIABILITY Unless otherwise expressly authoriz
START-UP REPORT FORM START-UP REPORT FORM This form is designed to record the initial installation, and to serve as a guide for troubleshooting at a
START-UP REPORT FORM presence? Are guide rails exactly vertical? Yes No Is base elbow installed level? Yes No Liquid level controls: Model Is
START-UP REPORT FORM Voltage supply at panel line connection, pump on L1-L2 L2-L3 L3-L1 Amperage load connection, pump on L1 L2 L3 FINAL CHECK Is p
NOTES:
BJM Pumps & Seal Minder is a registered trademark of BJM Pumps, LLC FARHENHEIT™ is a trademark of BJM Pumps, LLC. Copyright © 2006 – 2013 BJM Pu
TABLE OF CONTENTS INTRODUCTION ...
4 INTRODUCTION This Installation, Operation and Maintenance manual provides important information on safety and the proper inspection, disassembl
5 SAFETY Pump installations are seldom identical. Each installation and application can vary due to many different factors. It is the owner
6 INSPECTION Review all safety information before servicing pump. The following are recommended installation practices/procedures for the pump.
7 OIL FILL QUANTITY/TYPE Qty. oil in seal chamber Models U.S. fl. oz. C.C. Type of oil J400-F 5.1 150 ISO 32 NSF Food Grade Mineral Oil J750-F 9
8 POSITIONING THE PUMP BJM Pumps, J-F & JX-F Series pumps are designed to operate fully submerged. Data sheets can be obtained online at HHUU
9 PUMP ROTATION If wired properly to the control, the single phase BJM Pumps J-F and JX-F Series pump should operate with the correct pumping rota
Commentaires sur ces manuels